Get high throughput and low latency with your NVMe-enabled dual socket servers
by Rackspace Technology Staff
The need for access to high-speed, low-latency storage systems has become commonplace in today's server industry. Remember, only a few years ago, people considered SATA and SAS SSDs too expensive for everyday storage use.
Today, storage systems commonly consist of nothing but NAND-based products. I remember back in 2015 reading about multimillion-dollar storage systems that could provide a few million Input/Output Operations Per Second (IOPS). Here we
are in 2020, and I can exceed those numbers with a single system and for a few thousand dollars. Simply amazing.
Peripheral Component Interconnect (PCI)-based storage has had a mixed past with Fusion-IO ®, providing proprietary systems and drivers for high-speed performance. Luckily our industry overcame those vendor-centric models and delivered on a standard interface for PCI storage.
Non-volatile memory Express (NVMe) is the common name for providing NAND storage over a PCI express interface. It has an advantage over SAS and SATA in terms of protocol simplicity, bandwidth, and driver stacks designed for low latency and
high throughput. NVMe storage technology has been the industry leader in server storage performance. In its early days, NVMe was only available in a PCI half-height half-length (HHHL) card. This format made it difficult to scale systems to leverage a lot of NVMe storage.
Realistically, it was not feasible to install more than two or three NVMe devices per central processing unit (CPU). Now that U.2 (2.5 inch 15mm) form factors are readily available, scaling NVMe devices is as easy as scaling SAS or SATA devices. Because today you can easily scale your Rackspace® server to allow up to 12 NVMe devices, you have a new set of problems to think about. First, although these devices are much less expensive than they used to be, they are still relatively costly. How do you ensure that you are getting the most out of your investment? Second, because these devices connect directly to the processor's PCI bus, how do you ensure that performance and latency are predictable and consistent?
In this blog post, we explore the impact of NUMA controls in Linux® operating systems to determine the impact of latency and overall throughput.
We ran two simple experiments, one with NUMA control and one without NUMA control. Then, we explore the comparative results for latency, bandwidth, IOPs, and deviation of results between runs.
The experiment
To better describe the experiment, let me provide an example. With NVMe, storage attaches directly to a Peripheral Component Interconnect Express (PCIe) controller. That PCIe controller is embedded into the CPU package. If your server has one CPU, then all PCIe access is local. This configuration means the process that accesses the storage runs on the CPU where the storage is located. If your server has more than one CPU, then there is a possibility that the process accessing the storage is running on a CPU that does not have the PCI controller with your NVMe devices attached. Let's call this *non-local access*.
For non-local access to function, the CPU running the process must reach across the QuickPath Interconnect (QPI) links to access the other processor's PCI controller. Every time this happens, this should create some measure of latency.
This experiment determines the impact of local and non-local access, as shown in the following images:
The test setup for this experiment leverages the Rackspace R740xd platform with 12 NVMe devices and two Intel® Cascade Lake -R 6242R processors. We have 12 Intel 4610 1.6T NVMe SSDs.
For inducing I/O work on the drives, we leverage a flexible I/O tester (FIO). We are familiar with this benchmark, which includes the capability to direct the storage I/O processes at specific CPU cores. This setup works perfectly to allow both uncontrolled and controlled storage access.
The setup
We first ran an experiment to determine how many threads were required to push each SSD drive to its advertised performance limit. In our testing, we found that it took four threads of FIO with 64 outstanding operations to keep the drives completely busy and running at their advertised read limits. We then needed to understand the system's architecture. It is not always obvious what PCI lanes are attached to which NUMA domain. For this, we used a Linux tool called `lstopo -v` and the output of the `ls -al /sys/block/` command.
`ls -al /sys/block/` showed us the PCI bus number for each NVMe device. The `lstopo` output showed us how those PCI bus numbers mapped to the NUMA domains, where each of our NVMe devices was attached.
The following image shows our system:
With the output of `lspcu`, we could quickly determine what CPU cores were ineach NUMA domain, as shown in the following image:
With these details ironed out, we now know what CPU cores to leverage to access each NVMe device locally.
Our experiment has the following two test scenarios:
Scenario 1: No NUMA vontrol
Run the following command ten times. It performs random read access on all
drives at once and does not implement any NUMA control. It reads for a total of
100 seconds and uses a 30 second ramp time.
fio --direct=1 --ioengine=libaio --runtime=100 --group_reporting
--ramp_time=30 --time_based --refill_buffers --norandommap
--name=fio_read --rw=randrw --bs=4k --end_fsync=1 --rwmixread=100
--numjobs=4 --iodepth=64 --stonewall --filename=/dev/nvme0n1
--name=fio_read --rw=randrw --bs=4k --end_fsync=1 --rwmixread=100
--numjobs=4 --iodepth=64 --filename=/dev/nvme1n1 --name=fio_read
--rw=randrw --bs=4k --end_fsync=1 --rwmixread=100 --numjobs=4
--iodepth=64 --filename=/dev/nvme2n1 --name=fio_read --rw=randrw
--bs=4k --end_fsync=1 --rwmixread=100 --numjobs=4 --iodepth=64
--filename=/dev/nvme3n1 --name=fio_read --rw=randrw --bs=4k
--end_fsync=1 --rwmixread=100 --numjobs=4 --iodepth=64
--filename=/dev/nvme4n1 --name=fio_read --rw=randrw --bs=4k
--end_fsync=1 --rwmixread=100 --numjobs=4 --iodepth=64
--filename=/dev/nvme5n1 --name=fio_read --rw=randrw --bs=4k
--end_fsync=1 --rwmixread=100 --numjobs=4 --iodepth=64
--filename=/dev/nvme6n1 --name=fio_read --rw=randrw --bs=4k
--end_fsync=1 --rwmixread=100 --numjobs=4 --iodepth=64
--filename=/dev/nvme7n1 --name=fio_read --rw=randrw --bs=4k
--end_fsync=1 --rwmixread=100 --numjobs=4 --iodepth=64
--filename=/dev/nvme8n1 --name=fio_read --rw=randrw --bs=4k
--end_fsync=1 --rwmixread=100 --numjobs=4 --iodepth=64
--filename=/dev/nvme9n1 --name=fio_read --rw=randrw --bs=4k
--end_fsync=1 --rwmixread=100 --numjobs=4 --iodepth=64
--filename=/dev/nvme10n1 --name=fio_read --rw=randrw --bs=4k
--end_fsync=1 --rwmixread=100 --numjobs=4 --iodepth=64
--filename=/dev/nvme11n1 >>fio_output.txt
Scenario 2: Complete NUMA control.
To make this work, we needed to inject the following additional command options into the above script:
--numa_mem_policy=local
--cpus_allowed= <cores allowed>
This operation causes FIO to isolate memory to correct NUMA regions as well as to only run FIO processes where we want them to. All other command parameters like threads, outstanding I/O, and run/ramp time remain the same.
The results
Here are the results of our experiment.
As is typical in most storage performance benchmarking, this study uses IOPS as the metric to determine total storage throughput. Specifically, in our tests, we used an IOP size of 4 kilobytes. Over the ten runs, we consistently saw more than 6.3 million random 4k I/O operations with NUMA controls in place. With NUMA controls not leveraged, the system inconsistently ranged from a high of 6.2 million to a low of 6.071 million IOPS. Although a single system doing over six million IOPs is insanely fast, no one wants to leave performance on the table.
Average latency
Outside of just monitoring for total throughput, we also measured the average latency of I/O operations during the ten test runs.
The NUMA controlled benchmark showed very flat, predictable latencies that were lower overall than the non-NUMA controlled benchmark.
Per-drive performance deviation
Another way we wanted to look at this was in terms of per-drive consistent performance. For each of the ten passes, did the same drives always have a variance in performance? We first calculated the average IOPS for each drive across the ten runs.
Then we calculated the standard deviation (stdev) for the ten runs for each drive. The following graph represents the stdev as a percentage of the total operations performed.
Without NUMA, your performance can vary by as much as 1.4 to 1.8 percent from run to run. With NUMA controls in place, the performance stayed within .02 percent from run to run. Now, that is consistent!
Conclusion
Overall, our results show that leveraging NUMA to control process access to NVMe devices can provide not only an increase in overall throughput but also decrease the variability in system storage performance.
![Solve Insights Read Now Button](/sites/default/files/advertisements/Rackspace-Online-Ad-Solve-Ad-on-Blog-COM-TSK-8610.jpg)
Recent Posts
Escalando o penhasco da engenharia de plataformas: Uma jornada para a inovação e a eficiência
Julho 11th, 2024
Como funcionam as estratégias de fragmentação: Parágrafo, frase e técnicas inteligentes
Julho 4th, 2024
Arquitetura baseada em células na AWS
Maio 6th, 2024